Independent Wireless Multitasking LEDs blink using Arduino FreeRTOS

and send the data wirelessly using bluetooth module HC-05. :)



http://ift.tt/2bi4MpP.

The code
#include <Arduino_FreeRTOS.h>
#include <SoftwareSerial.h>
SoftwareSerial mySerial(10, 11); // RX, TX

int n = 0;

// define two tasks for Blink & AnalogRead
void TaskBlink( void *pvParameters );
void TaskBlink2( void *pvParameters );
void TaskBlink3( void *pvParameters );
void TaskBlink4( void *pvParameters );
void TaskTadaa( void *pvParameters );

// the setup function runs once when you press reset or power the board
void setup() {
   // initialize serial communication at 9600 bits per second:
  mySerial.begin(9600);  

  // Now set up two tasks to run independently.
  xTaskCreate(
    TaskBlink
    ,  (const portCHAR *)"Blink"   // A name just for humans
    ,  128  // Stack size
    ,  NULL
    ,  2  // priority
    ,  NULL );
  xTaskCreate(TaskBlink2,(const portCHAR *)"Blink2",128, NULL,2,NULL );
  xTaskCreate(TaskBlink3,(const portCHAR *)"Blink3",128, NULL,2,NULL );
  xTaskCreate(TaskBlink4,(const portCHAR *)"Blink4",128, NULL,2,NULL );

  xTaskCreate(
    TaskTadaa
    ,  (const portCHAR *) "Tadaa"
    ,  128 // This stack size can be checked & adjusted by reading Highwater
    ,  NULL
    ,  1  // priority
    ,  NULL );

  // Now the task scheduler, which takes over control of scheduling individual tasks, is automatically started.
}

void loop()
{
  // Empty. Things are done in Tasks.
}

/*--------------------------------------------------*/
/*---------------------- Tasks ---------------------*/
/*--------------------------------------------------*/

void TaskBlink(void *pvParameters)  // This is a task.
{
  (void) pvParameters;

  // initialize digital pin 13 as an output.
  pinMode(13, OUTPUT);

  for (;;) // A Task shall never return or exit.
  {
    digitalWrite(13, HIGH);   // turn the LED on (HIGH is the voltage level)
    mySerial.println("LED 13 Nyala");
    vTaskDelay( 1000 / portTICK_PERIOD_MS ); // wait for one second
    digitalWrite(13, LOW);    // turn the LED off by making the voltage LOW
    mySerial.println("LED 13 Padam");
    vTaskDelay( 1000 / portTICK_PERIOD_MS ); // wait for one second
  }
}
void TaskBlink2(void *pvParameters){
  (void) pvParameters;
  pinMode(2, OUTPUT);
  for (;;) {
    digitalWrite(2, HIGH); vTaskDelay( 2000 / portTICK_PERIOD_MS );mySerial.println("LED 2 Nyala");
    digitalWrite(2, LOW);  vTaskDelay( 2000 / portTICK_PERIOD_MS );mySerial.println("LED 2 Padam"); 
  }
}

void TaskBlink3(void *pvParameters){
  (void) pvParameters;
  pinMode(3, OUTPUT);
  for (;;) {
    digitalWrite(3, HIGH); vTaskDelay( 500 / portTICK_PERIOD_MS );mySerial.println("LED 3 Nyala");
    digitalWrite(3, LOW);  vTaskDelay( 1500 / portTICK_PERIOD_MS );mySerial.println("LED 3 Padam"); 
  }
}

void TaskBlink4(void *pvParameters){
  (void) pvParameters;
  pinMode(4, OUTPUT);
  for (;;) {
    digitalWrite(4, HIGH); vTaskDelay( 500 / portTICK_PERIOD_MS );mySerial.println("LED 4 Nyala");
    digitalWrite(4, LOW);  vTaskDelay( 250 / portTICK_PERIOD_MS );mySerial.println("LED 4 Padam"); 
  }
}

void TaskTadaa(void *pvParameters)  // This is a task.
{
  (void) pvParameters;
  for (;;)
  {
    // read the input on analog pin 0:
    n++;
    if (n>100){n = 0;}
    // print out the value you read:
    mySerial.print("Tadaa...");
    mySerial.println(n);
    vTaskDelay(2000/portTICK_PERIOD_MS);// 2 second delay
    // one tick delay (15ms) in between reads for stability
  }
}